Προσοχή! Η σελίδα αυτή χρησιμοποιεί cookies για να σας προσφέρει καλύτερη εμπειρία χρήσης, με την συνέχεια της λειτουργίας της αποδέχεστε την λειτουργία αυτή. OK
LokBuild Print Surface 305x305mm High efficiency adhesion for PrintBeds

LokBuild Print Surface 305x305mm High efficiency adhesion for PrintBeds

LOKBUILD, 305x305mm
 
18.95
(23.50 με Φ.Π.Α.)
1116.929
Σε Απόθεμα
+
Προσθήκη στη Λίστα Αγαπημένων
  • Χαρακτηριστικά
LOKBUILD FEATURES
  • Optimal 3D Printing Surface
  • Improves Model Adhesion
  • Reduces Warping
  • Easier Nozzle Height Calibration
  • Durable and Long Lasting
  • Protect your Build Plate
  • Easy Removal of Completed Prints
  • One Build Surface for most materials
  • Easy to Install and Remove
HOW TO USE LOKBUILD

If you have ever used tape or films you will know that they are difficult to fit. LokBuild is more rigid and really easy to apply to your build plate. Also it is almost impossible for air bubbles to get trapped beneath the LokBuild surface.

LokBuild can be removed from the build plate cleanly in one piece and leaves no residue behind.

INSTALLATION

1) Wipe down the build platform making sure it is clean.

2) Trim LokBuild to match the shape and size of your build plate. This can be done easily with general household scissors or a craft knife.

3) Remove the adhesive backing and apply LokBuild to the build plate. Start from one side and work your way to the other side, smoothing LokBuild as you go.

4) Adjust the printers nozzle height and check that the build surface is level.


HOW TO CLEAN LOKBUILD

LokBuild should not need to be cleaned very often but if you do please use alcohol wipes or similar (low % Isopropyl). Do not use acetone or anything with a high % Isopropyl, this will damage the surface.

NOZZLE HEIGHT CALIBRATION

LokBuild is much more forgiving than some other products when setting the nozzle height and does not require such a high level of accuracy. However there will be an optimal nozzle height for your chosen material and printer.

The key to a good nozzle height is to experiment. We recommmend starting further away from the bed than with other surfaces and then reduce the nozzle height slightly until the print sticks to LokBuild.

The vast number of printers and materials makes it impossible to give exact print parameters but a good starting point for the nozzle height would be between 0.20mm - 0.25mm.

TIP: When setting the nozzle height start further away from the bed than with other surfaces such as tapes. LokBuild works better without squashing the filament too much on the first layer.

 

PREVENT WARPING / EFFORTLESS MODEL REMOVAL

LokBuild creates an excellent bond between 3D printed models and the build surface while preventing curling and warping. When prints are completed the model can be cleanly removed with minimal effort. This is a vast improvement over the excessive scraping and forcing involved with some of the alternatives.

BUILD PLATE PROTECTION

Another big advantage of LokBuild is its durable finish. It is very effective at protecting the build plate. It is heat resistant and durable and can be reused for many consecutive prints. You can also use LokBuild with many different types of filament without needing to change the printing surface.

CALIBRATION

LokBuild is much more forgiving than some other products when setting the nozzle height and does not require such a high level of accuracy. This makes the calibration process much simpler and printing more enjoyable. TIP: When setting the nozzle height start further away from the bed than with other surfaces such as tapes.

EASY INSTALLATION

If you have ever used tape or films you will know that they are difficult to fit. LokBuild is more rigid and really easy to apply to your build plate. Also it is almost impossible for air bubbles to get trapped beneath the LokBuild surface. LokBuild can be removed from the build plate cleanly in one piece and leaves no residue behind.

Αγορές που έγιναν μαζί με το παραπάνω προϊόν