Τεχνικές ερωτήσεις για ηλεκτρονικά εξαρτήματα θα εξυπηρετούνται μέσω τηλεφώνου Δευτέρα εως Παρασκευή καθώς δεν υπάρχει τεχνικός για δια ζώσης εξυπηρέτηση στο φυσικό κατάστημα. Επίσης τα Σάββατα προσωρινά δεν υπάρχει καθόλου τεχνικός ηλεκτρονικών

Σχετικά με την κάλυψη διαθέσιμης θέσης ηλεκτρονικού μπορείτε να στέλνετε βιογραφικά στο iraklis@cableworks.gr

L298N 1.5A Dual Channel H-Bridge Stepper / DC Motor PWM Driver Module
Κωδικός Cableworks: 1116.373

BrandOEM MPNOEM
2.80
χωρίς ΦΠΑ 2.26
Σε Απόθεμα
+
Wishlist
Αποστολές & Επιστροφές
Τρόποι πληρωμής
Γιατί Cableworks;
Γρήγορη και ασφαλής παράδοση

Αποστέλλουμε παραγγελίες σε όλη την Ελλάδα με ΕΛΤΑ Courier και ACS

Presales και Aftersales

Για να σας λύνονται όλες οι τεχνικές απορίες

Επιστροφές εντός 14 ημερών

Αρκεί το προϊόν να μην έχει ανοιχτεί και να μην έχουν προκληθεί φθορές στην συσκευασία του

CABLEWORKS

Αναλυτική Παρουσίαση

Description:

  • Motor drive module is ideal for use in battery-powered smart car, toy cars, robots. Supply voltage 2V ~ 10V, can drive two DC motors or a 4-wire 2-phase stepper motors ,can achieve forward rotation or reverse rotation, it is possible to adjust the rotation speed. Each can provide continuous current of 1.5A, peak current up to 2.5A, thermal protection and can be automatically restored.

Product Highlights:

  • Use of imported original chip, built-in low on-resistance MOS switch, minimal heat, no heat sink, small size, low power consumption, is ideal for battery powered.
  • (L298N internal transistor switch, low efficiency, high fever, need to add heat sink, bulky, L298N very easy to burn).
  • Dual 1.5A * 2, the peak current to be 2.5A, built-in thermal protection circuit, do not be afraid motor stall burned, automatic recovery after the temperature dropped.
  • Small size, light weight, 0 standby current, is the ideal choice for your car model.

Product parameters:

  • Dual H-bridge motor driver, can drive two DC motors or a 4-wire two-phase stepper motor.
  • The module supply voltage 2V-10V.
  • Signal input voltage 1.8-7V.
  • Single Operating current 1.5A, peak current up to 2.5A, low standby current (less than 0.1uA).
  • Built-in common conduction circuit, when the input pin is left floating, the motor does not malfunction.
  • Built-in thermal protection circuit with hysteresis effects (TSD), without worrying about motor stall.
  • Product Size: 24.7 * 21 * 5mm (length, width, height), ultra-small size.
  • The mounting hole diameter: 2 mm.

Precautions:

  • Power positive and negative reversed will certainly cause damage to the circuit.
  • Output is shorted to ground or output short circuit, and the motor stall, the chip will heat protection, but in the near or exceeding 10V voltage and peak current is greater than 2.5A situation can also cause chip burned.

Cableworks

Τεχνικές Προδιαγραφές

Brand:
OEM
MPN:
OEM
SFP28 (25G):

Cableworks

Ρωτήστε μας

Cableworks

Αξιολογήσεις

Δε βρέθηκαν αξιολογήσεις

  • QoS
  • Νομοθεσία

Cableworks

BEST SELLERS