Τεχνικές ερωτήσεις για ηλεκτρονικά εξαρτήματα θα εξυπηρετούνται μέσω τηλεφώνου Δευτέρα εως Παρασκευή καθώς δεν υπάρχει τεχνικός για δια ζώσης εξυπηρέτηση στο φυσικό κατάστημα. Επίσης τα Σάββατα προσωρινά δεν υπάρχει καθόλου τεχνικός ηλεκτρονικών

Σχετικά με την κάλυψη διαθέσιμης θέσης ηλεκτρονικού μπορείτε να στέλνετε βιογραφικά στο iraklis@cableworks.gr

Original E3D Experimental High-Resolution v6 Nozzle - 1.75mm x 0.15mm
Κωδικός Cableworks: 1134.081

BrandE3D MPNV6-NOZZLE-175-150
22.88
χωρίς ΦΠΑ 18.45
Μη Διαθέσιμο
Wishlist
Αποστολές & Επιστροφές
Τρόποι πληρωμής
Γιατί Cableworks;
Γρήγορη και ασφαλής παράδοση

Αποστέλλουμε παραγγελίες σε όλη την Ελλάδα με ΕΛΤΑ Courier και ACS

Presales και Aftersales

Για να σας λύνονται όλες οι τεχνικές απορίες

Επιστροφές εντός 14 ημερών

Αρκεί το προϊόν να μην έχει ανοιχτεί και να μην έχουν προκληθεί φθορές στην συσκευασία του

CABLEWORKS

Αναλυτική Παρουσίαση

0.15mm Experimental High-Resolution Nozzle

This 0.15mm nozzle allows you to print some really, seriously, very, extremely tiny parts with with a level of fine detail that will blow you away. We wrote a whole blog post about it!

For complete requirements and specifications check our blog and documentation pages.

WARNING: This precision nozzle for 3D printing has been engineered by E3D to be as user-friendly as possible, but nonetheless has some very specific requirements!

  • For use with high-flow filaments like MG94-ABS, PC-ABS, PMMA, or an ASA like MatX
  • Always use clean, high-quality filament
  • Requires the use of a geared extruder (e.g. Titan), silicone sock and part-cooling fan
  • Keep clean and dust-free to avoid blockage

Slicer Settings:

    Nozzle Size: 0.15mm (obviously!)
  • Layer Height: We recommend somewhere in the region of 0.08mm. This proved to be the sweet-spot for us.
  • Print Speeds: Make sure to turn your speeds and acceleration down. This is all about precision, and precision takes time. We ran our printers at 18mm.s-1, with outline and infill under-speeds at 75-80%. The overhangs were left at the default 45°, and the minimum infill length at 5 mm.
  • Retraction: Stringing can be almost entirely tuned away in your retraction settings, however poor tuning can make things much worse due to the higher extrusion forces and pressures. We were using 1mm at 30mm/s.

Cableworks

Τεχνικές Προδιαγραφές

Brand:
E3D
MPN:
V6-NOZZLE-175-150

Cableworks

Ρωτήστε μας

Cableworks

Αξιολογήσεις

Δε βρέθηκαν αξιολογήσεις

  • QoS
  • Νομοθεσία

Cableworks

BEST SELLERS